Ge-industrial-solutions Spectra Series Power Panelboards APN and APNB User Manual download pdf

Spectra Series™ Power Panelboards

Type APN and APNB Panelboard Interiors into

Type APB Panelboard Enclosures

Installation

WARNING: Dan

er of electrical shock or in

Turn OFF

ower ahead of the

anelboard or

switchboard before workin

inside the e

ment or

removin

com

onent. E

ment is to be

installed and maintained b

erl

trained and

qualified personnel only.

These instructions describe the installation of Type APN and

APNB panelboard interiors into Type APB panelboard

enclosures. Figure 1 shows a typical panel with four-piece trim.

Figure 2 shows a typical panel with a dead front and the door

removed.

Figure 1. Typical panel with four-

piece trim.

Figure 2. Typical panel with a

deadfront.

1. For ease of installation, it is necessary to remove the filler

plates and, if provided, the deadfront assembly. When

removing the deadfront, remove only the side rails and line-

end filler plate, leaving the mounting posts and load-end

filler attached, as shown in Figure 3. Follow the

instructions for removal provided with each device, and set

aside.

NOTE: For panels not assembled at the factory, but that

require a deadfront, attach the mounting posts provided with

the deadfront kit at this time, following the instructions

provided with the kit.

2. Remove the four wing nuts and washers from the

/8"

interior mounting studs on the back wall of the enclosure.

3. Locate the panel mounting studs that align with the

panelboard interior mounting holes, as shown in Figure 4.

The line end of the panel must be installed toward the line

end of the box.

Figure 3. Deadfront assembly removed.

Figure 4. Panelboard mounting studs.

4. Place the interior on the studs, and replace the washer and

wing nuts. Tighten the wing nuts.

5. Reinstall any filler plates removed earlier, starting at the

lower end of the interior. For device installation, refer to

the instructions furnished with the device. Once installation

is complete, wiring may be brought to the main and branch

devices. See the aluminum termination caution below.

GEH5589 Installation Instructions R07

Reference

Figure 6

Side Rail

End Filler

Load-End

Filler with

Labels

Enclosure

Back

Reference

Figure 5 or 7

Mounting

Post

1 2

Summary of Contents

Page 1 - Installation

gSpectra Series™ Power PanelboardsType APN and APNB Panelboard Interiors intoType APB Panelboard EnclosuresInstallationWARNING: Danger of electrica

Page 2 - Terminations

Panels with Full-Height Door Fronts6. If a full-height door front is to be used on the panel, it isnecessary to reinstall the deadfro

Ge-industrial-solutions Spectra Series Power Panelboards APN and APNB User Manual

Browse online or download User Manual for Equipment Ge-industrial-solutions Spectra Series Power Panelboards APN and APNB. GE Industrial Solutions Spectra Series Power Panelboards APN and APNB User Manual [en]

Summary of Contents

More documents for Equipment Ge-industrial-solutions Spectra Series Power Panelboards APN and APNB

Comments to this Manuals

Ge-industrial-solutions Spectra Series Power Panelboards APN and APNB User Manual

Browse online or download User Manual for Equipment Ge-industrial-solutions Spectra Series Power Panelboards APN and APNB. GE Industrial Solutions Spectra Series Power Panelboards APN and APNB User Manual [en]

Summary of Contents

More documents for Equipment Ge-industrial-solutions Spectra Series Power Panelboards APN and APNB

Comments to this Manuals

Related products and manuals for Equipment Ge-industrial-solutions Spectra Series Power Panelboards APN and APNB