Ge-industrial-solutions AF-600 FP Redundant Drive Panels User Manual

DEH40633 AN 12-1007, Rev.04, 04/04/2012 Section Topic 1 Thanks information – DEH40639 2 Installation and Start-up Instruct

DEH40634 AN 11-1018 Rev.02, 09/26/2011 1. Operator Devices Your Redundant Drive panel is equipped with several panel door mounted o

DEH40634 AN 11-1018 Rev.02, 09/26/2011 Hand/Off/Auto Selector This selector is also referred to as the H-O-A switch. In the

DEH40634 AN 11-1018 Rev.02, 09/26/2011 Emergency Stop This operator is used to shut off the panel output in case of Emergency. To restart th

DEH40634 AN 11-1018 Rev.02, 09/26/2011 CTB1-1 through CTB1-3 Customer Safety Interlocks. Put normally closed contacts between CTB-1 and

DEH40634 AN 11-1018 Rev.02, 09/26/2011 Relay 1 – 01,02,03 Normally open inverter fault contacts. These contacts are utilized to energize an in

DEH40634 AN 11-1018 Rev.02, 09/26/2011 protection. UL listed Class J time-delay fuses are provided with your panel. These fuses have been s

DEH40634 AN 11-1018 Rev.02, 09/26/2011 Relay 1 (E24) Set to “9” Alarm Relay 2 (E24) Set to “5”Running Electronic Overload (F10)

DEH40634 AN 11-1018 Rev.02, 09/26/2011 6. Troubleshooting Drive1 and Drive2 Motor Rotation If careful attention to phase rotation is not mad

DEH40637 AN 10-2100, Rev.01, 10/20/2010 AF-600 FP User’s Guide DET -609 AF 600 FP User’s Guide for up to 60HP @ 208V @ & up

DEH40636 AN 11-1018, Rev.02, 09/26/2011 Table A 460 VAC Panel Current Ratings and Maximum Allowable Fuse Sizes In-

DEH40639 AN 10-2100 Rev 01, 10/20/2010 GE Drives wishes to thank you for choosing our adjustable frequency controller product. We

DEH40636 AN 11-1018, Rev.02, 09/26/2011 Table A AF 600 Redundant Drive Panels – 460 VAC Current Ratings and Maximum Fuse Sizes

DEH40638 AN 10-2100, Rev.01, 10/20/2010 In-Warranty Information Form The purpose of this form is to provide specific information to G

DEH40638 AN 10-2100, Rev.01, 10/20/2010 Once all the required information above is acquired, contact the following number for assista

DEH40635 AN 12-1007 Rev.02, 04/04/2012 Table 1 Wire Sizes and Torque Requirements for 460 VAC Panels Table 2 UL508 Requirement- Tight

DEH40635 AN 12-1007 Rev.02, 04/04/2012 Table 2 UL508 Requirement Table 54.1 , Tightening torque for screws Test wire size installed in connector

DEH40635 AN 12-1007 Rev.02, 04/04/2012 Table 54.2 , Tightening torque for slotted head screws smaller than No. 10 intended for use with 8 AWG or

DEH40635 AN 12-1007 Rev.02, 04/04/2012 Table A Redundant drive panel HP Ratings Estimated Watt Loss (Watts) at 460V 15 432 20 572 25 673 30 731

DEH40632 AN 12-1007, Rev.03, 04/04/2012 The following information is provided for reference use during the installation of your AF-

DEH40632 AN 12-1007, Rev.03, 04/04/2012 The environments for NEMA Type 1 enclosures shall be indoor where the following condition may exist; falling

DEH40632 AN 12-1007, Rev.03, 04/04/2012 GROUNDING All panels/enclosures must be grounded. All exposed metal parts are connected

DEH40632 AN 12-1007, Rev.03, 04/04/2012 CONTROL WIRING (120 VAC ) All field wiring shall have a minimum insulatio

DEH40632 AN 12-1007, Rev.03, 04/04/2012 AF-600 Redundant Drive Panels require no additional signal wiring to operate properly. Additional

DEH40634 AN 11-1018 Rev.02, 09/26/2011 Your AF 600 Redundant Drive Panel comes with an AF 600 FP Adjustable Frequency Drive from GE

DEH40634 AN 11-1018 Rev.02, 09/26/2011 1. Operator Devices page 3 2. Customer Terminal Board page 5 3.